Check whether water appears at the supply hose, drain hose, or over the tub rim. Whirlpool’s drain guide calls out hose placement and kinks; load overload and suds may leave clothes wet but do not prove a tub leak. Close water valves for an active hose leak and arrange repair.
Look at the hose route and overflow evidence
Check whether water appears at the supply hose, drain hose, or over the tub rim.
Close water valves for an active hose leak and arrange repair.
Whirlpool 2622751 is listed as Top-Loading. For this recorded top-loading Whirlpool design, place the first inspection at the lid, basket rim, fitted dispenser and the visible fill/drain connections. For a spin complaint, separate retained water from an uneven load, then check the selected cycle and lid state. Keep clothing loose enough to move; an agitator, impeller or automatic-fill procedure needs its own feature match.
Locate when water appears and whether it returns during fill, wash, or drain. Safe visible checks can distinguish hose and drain issues from condensation or a spill.
Owner guide: Leaks, moisture & condensation
Category & symptom guidance
Leaks, moisture & condensation
3 minute read · Shared guidance for washing machines
Contain water and locate its path
If water is spreading, pause the washer and close the household hot and cold supply valves if they are accessible without stepping into standing water. Keep clear of wet electrical connections. Blot the area and identify the first wet point: behind the washer, beneath a hose connection, at the drain, around the door, or in front of a dispenser.
A damp floor after a detergent spill or an overfilled dispenser has a different pattern from a steady leak during fill. Dry the area, then watch from a safe distance during a short, attended cycle only if the leak is minor and there is no electrical or structural hazard. Do not leave a suspected leak running unattended.
Inspect visible supply connections
With the washer stopped, look for drips at the hot and cold hose ends and along the visible hose length. Check for a loose-looking coupling, a kink, cracking, or abrasion without pulling the washer away from the wall if that could strain the hoses. A leak at a hose connection points toward the supply side; water that appears only during draining may come from the drain path instead.
If a hose is split, badly worn, or leaking continuously, close the supply valves and arrange replacement. Do not tighten a damaged fitting aggressively or use tape as a substitute for a sound seal. Installation guidance for the LG WM4000H*A calls for new hoses and checking seals at both ends; this is model-family guidance, not proof that a particular hose fits another washer.
Trace water during draining
If moisture appears when the washer pumps out, inspect the visible drain hose for a kink, dislodged end, or water escaping where it enters the household drain. A loose hose can spill water even when the washer itself is working. Do not push the hose deeper, seal the drain opening airtight, or change its height by guesswork; drain arrangements and limits vary by model.
For the LG WM4000H*A, the manual specifies a secured hose and warns against an airtight seal because siphoning can remove water from the drum. Use that instruction only for the named family; for another washer, follow its installation diagram and local plumbing requirements.
Check door, dispenser, and moisture patterns
A front-loader can show water around the door if laundry or debris prevents the seal from closing evenly. When stopped, inspect the visible seal for an item caught at the edge and wipe away residue; do not pull, cut, or dismantle the seal. Oversudsing from excess or unsuitable detergent can send suds or water toward the dispenser area, so compare the detergent amount with its package directions and the washer’s guidance.
Some moisture may be condensation or a small splash rather than an active leak. Dry the area and see whether it returns at the same cycle stage. Persistent water from beneath the cabinet, a torn seal, or a leak that cannot be traced from visible points calls for service.
What to do with what you find
Water drips from a visible supply hose or coupling while filling.
The supply connection or hose may be compromised.
Close the valves and replace or correct the visible connection using model-appropriate instructions.
Water appears only as the washer drains.
The drain hose or household drain connection may be dislodged or obstructed.
Check visible routing and secure placement; stop if it continues to spill.
Water persists from under the cabinet or around a damaged door seal.
The leak likely needs inspection beyond routine surface cleaning.
Stop use and arrange service.
Have these details ready
First wet location
Whether leak begins during fill, wash, or drain
Visible hose, drain, door, or dispenser condition
Whether the area stays wet after drying
Common questions
Is moisture around the washer always a leak?
No. A spill, condensation, oversudsing, or a drain connection can leave moisture. Dry the area and note whether water returns at a specific cycle stage.
Can I run another cycle to find the leak?
Only if the moisture is minor, the supply and electrical area are dry, and you can attend the washer. Stop immediately if water flows, spreads, or appears near electrical parts.
General background sources
These sources support the shared guide. Exact model specifications and matched family procedures have their own sources above.