Appliance & electronics support
Find your model numberAbout our sources
Samsung DV25FG60BVBEA2 product photo
Photo: DV25FG60BVBEA2. Photo source
Manufacturer sources

Samsung DV25FG60BVBEA2

Installation planning

Clothes dryer · US market · 44 owner topics

Samsung dryers

Guidance for Samsung clothes dryers. Check the feature and control descriptions against your model.

Samsung dryers

Check fit and stack kit by exact pair

Samsung offers standalone dryers, stacked washer/dryer pairs, laundry hubs, and ventless or vented combos. The product category page shows those as different installation solutions. Before ordering a stacking kit or planning a duct, match both product codes and read the exact installation guide. Confirm door swing, floor support, utilities, and exhaust design; a standard-looking Samsung dryer may not share another unit’s dimensions or hookups.

Specifications & model details

DV25FG60BVBEA2: model-specific checks

What is recorded for DV25FG60BVBEA2

Samsung DV25FG60BVBEA2 — Manufacturer width (decimal specification): 23.6; Manufacturer height (decimal specification): 33.5; Manufacturer depth (decimal specification): 25.8.

Use these measurements for the first comparison

For Samsung DV25FG60BVBEA2, start with manufacturer width (decimal specification) 23.6, manufacturer height (decimal specification) 33.5, manufacturer depth (decimal specification) 25.8. Preserve those labels when comparing an opening or delivery route. Any handle/hinge allowances, clearances and adjustment ranges that the source does not establish remain additional checks.

Prepare the location by confirming dryer type, utilities, exhaust or condensation handling, clearances, delivery access, and any model-specific accessories.

Owner guide: Installation planning

Category & symptom guidance

Installation planning

Identify what the home and dryer require

Before delivery, establish the dryer’s exact model and whether it is gas or electric. Then compare its installation instructions with the utilities actually present: electrical supply, gas connection where applicable, and the exhaust or condensate arrangement required by the design. A similar cabinet or product-family name does not establish that the connections match.

Dryers may be vented, condenser, or heat-pump designs. A vented unit sends moist air through an exhaust duct; condenser and heat-pump units manage moisture differently and may need a drain or collection arrangement specified by their instructions. Do not plan a new unit around an existing vent opening until the selected dryer type is known.

Prepare a vented-dryer exhaust route

For a vented dryer, inspect where the duct begins, where it exits outdoors, and whether the route is accessible for cleaning. Confirm the exact model’s permitted duct material, diameter, length, bends, and outlet requirements in its installation guide. Keep the route as direct as the instructions allow and avoid a plan that leaves the connector crushed when the dryer is moved into place.

Some models permit more than one exhaust direction, often with a specific kit. Verify kit compatibility and the resulting spacing before cutting or altering cabinetry. Do not discharge dryer exhaust into a wall, attic, crawlspace, or room. If the existing route is damaged, obstructed, or ends indoors, arrange correction before normal use.

Plan gas or electric connections correctly

An electric dryer needs the supply and cord arrangement specified for its exact model and jurisdiction. A gas dryer also needs the correct electrical supply, plus a suitable gas connection; its small electrical rating does not eliminate the fuel requirement. Do not adapt a plug, change wiring, or connect gas based on a family brochure. Confirm the site and installation plan with the installer before the appliance arrives.

If a gas model is being converted for a different fuel, verify whether the manufacturer lists a conversion procedure and the exact kit for that model. A kit listed for one family is not universal, and conversion is not an owner improvisation. Make sure the installer knows the fuel available and the model code before work begins.

Check the site and delivery details

Measure the delivery route and final location, including door swing, overhead space, wall projections, and room for utility connections. Remove loose items from the route and identify any fragile flooring or narrow turn before delivery. Tell the retailer if the dryer will be stacked, placed on a pedestal, or routed through a tight opening so the delivery plan can account for the configuration.

For a closet, follow the exact model’s opening and ventilation requirements. Some manufacturer instructions specify upper and lower air openings; do not substitute a closed door or assume a louvered panel meets the area requirement without checking. Keep access for lint-filter removal and future service in the layout.

Complete setup checks before routine use

After placement, the installer should verify leveling, stable footing, utility connections, exhaust attachment for vented designs, and that no cord or duct is pinched. Review the owner instructions for first-use checks and controls. If the model has an installation-check feature, use it only as directed in that model’s manual; a feature described on another model’s sheet is not evidence yours includes it.

For condenser or heat-pump designs, confirm that the condensate container or drain is set up as instructed and that filters and heat-exchanger access remain clear. Do not apply vented-dryer airflow assumptions to these machines. Keep the completed installation information and any conversion or accessory details with the appliance record.

What to do with what you find

The utility and exhaust or moisture-handling plan matches the exact dryer instructions.

The site is prepared for the selected design and fuel type.

Confirm delivery access, accessories, and installer scope.

The home connection is uncertain, or a vented unit’s route ends indoors or is obstructed.

The appliance should not be put into routine service under the current plan.

Resolve the connection or duct route before installation.

Have these details ready

  • Full dryer model code and installation instructions
  • Site utility details and fuel available
  • Exhaust route or condensate arrangement, depending on dryer design
  • Delivery route and final-space measurements

Common questions

Can I reuse the old dryer vent for any new dryer?

Only if the selected dryer is vented and the route meets its instructions, is intact, and terminates outdoors.

Does a gas dryer need an electrical connection?

Yes. It needs the electrical supply specified for that model as well as its gas connection.

General background sources

These sources support the shared guide. Exact model specifications and matched family procedures have their own sources above.

  1. www.energy.gov/cmei/buildings/consumer-clothes-dryers
  2. www.lg.com/us/support/products/documents/DLEX4000_%20DLGX4001_%20Spec%20Sheet.pdf
  3. www.lg.com/us/support/product/lg-DLEX4000W.ABWETUS?tab=1
  4. www.cpsc.gov/Safety-Education/Safety-Guides/Home-Fire-Electronics-and-Electrical/Overheated-Clothes-Dryers-Can-Cause-Fires

Owner guidance by Specs & Parts, drafted with GPT-6 Luna. Sources and scope.

Recorded model facts

Model details relevant to this topic

SpecificationRecorded valueEvidence
Manufacturer depth (decimal specification)25.8
Manufacturer
Samsung US current manufacturer catalog

Exact primary manufacturer SKU DV25FG60BVBEA2; https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Exact modelCode in manufacturer technical specification response. Primary source: https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Observed Oct 30, 2026
Manufacturer height (decimal specification)33.5
Manufacturer
Samsung US current manufacturer catalog

Exact primary manufacturer SKU DV25FG60BVBEA2; https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Exact modelCode in manufacturer technical specification response. Primary source: https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Observed Oct 30, 2026
Manufacturer width (decimal specification)23.6
Manufacturer
Samsung US current manufacturer catalog

Exact primary manufacturer SKU DV25FG60BVBEA2; https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Exact modelCode in manufacturer technical specification response. Primary source: https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Observed Oct 30, 2026
Product Dimensions (W x H x D)23.6" W x 33.5" H x 25.8" D
Manufacturer
Samsung US current manufacturer catalog

Exact primary manufacturer SKU DV25FG60BVBEA2; https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Exact modelCode in manufacturer technical specification response. Primary source: https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Observed Oct 30, 2026
Shipping Dimensions (W x H x D)26.4" x 34.8" x 27.4"
Manufacturer
Samsung US current manufacturer catalog

Exact primary manufacturer SKU DV25FG60BVBEA2; https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Exact modelCode in manufacturer technical specification response. Primary source: https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Observed Oct 30, 2026
Width Compact (24")Yes
Manufacturer
Samsung US current manufacturer catalog

Exact primary manufacturer SKU DV25FG60BVBEA2; https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Exact modelCode in manufacturer technical specification response. Primary source: https://www.samsung.com/us/laundry/dryers/electric-4-cu-ft-compact-dryer-in-white-sku-dv25fg60bvbea2

Observed Oct 30, 2026

Sources for DV25FG60BVBEA2

Suggest a correction